攪拌車液壓件的“致病”因素分析
混凝土攪拌車液壓的“致病”因素：污染、過熱和進入空氣。如果懂得一些常識原理，知道導致故障的3個有害因素，就能使攪拌車長期處于良好的工作狀態。
"Pathogenic" factors of hydraulic pressure of concrete mixer: pollution, overheating and entering air. If you know some common sense principles and know the three harmful factors leading to the failure, you can make the mixer in good working condition for a long time.
一，攪拌車工作油液進入雜質而變質，進入油液中的雜質的來源有灰、砂、土等：
1、 The working oil of the mixer truck deteriorates due to impurities. The sources of impurities in the oil include ash, sand, soil, etc
液壓件外部不清理，不清理雜質加油被帶入系統，或通過損壞密封圈進入系統
The outside of the hydraulic parts is not cleaned, impurities are not cleaned, and the refueling is brought into the system, or enters the system by damaging the sealing ring
內部清理不干凈，在油箱或部件內容易留下微量的雜質
If the internal cleaning is not clean, it is easy to leave trace impurities in the oil tank or components
加油容器，用具要干凈
The refueling container and utensils shall be clean
油液存方不當，在加入前油就不干凈或已變質
The oil is stored improperly, and the oil is not clean or deteriorated before adding
已經變質的油會損壞零件。被損壞的金屬離分子懸浮在油中。
Deteriorated oil can damage parts. The damaged metal molecules are suspended in the oil.
雜質會造成零件的損壞與腐蝕，尤其是對于精加工的部件，它們會擦傷皮管的內壁、油封圈和填料，而這些東西損壞后又會導致液壓系統無法正常工作。
Impurities will cause damage and corrosion of parts, especially for finished parts, they will scratch the inner wall of leather pipe, oil seal ring and packing, and these things will cause the hydraulic system to fail to work normally after being damaged.
二，液壓系統過熱可能是以下一種或多種原因造成：
2、 Overheating of the hydraulic system may be caused by one or more of the following reasons:
當油中進入空氣或水分，液壓泵把油液轉變?yōu)閴毫r，空氣和水分就會因熱量增加導致過熱
When air or moisture enters the oil and the hydraulic pump changes the oil into pressure, the air and moisture will overheat due to the increase of heat
液壓系統內的油平面過高，油液強烈攪動，而引起過熱
The oil level in the hydraulic system is too high and the oil is stirred strongly, resulting in overheating
質量較差的油可能變稀，使外來物質漂浮或與水有親合力，這樣也會引起過熱
Poor quality oil may become thinner, causing foreign substances to float or have affinity with water, which will also cause overheating
工作時超負荷工作，也會產生熱量
Working overload will also produce heat
回油閥調整不當或未及時更換已損壞零件，也會產生熱量。
Improper adjustment of the return valve or failure to replace damaged parts in time will also generate heat.
三，當空氣進入油液中會導致下列幾種情況：
3、 When air enters the oil, it will cause the following conditions:
當加油時操作不當，導致有氣泡混入油內而帶入油管中
Improper operation during refueling causes bubbles to mix into the oil and bring them into the oil pipe
接頭松動或油封破損，工作時候空氣被吸入
The joint is loose or the oil seal is damaged, and the air is sucked in during operation
油管路被磨穿、擦破或腐蝕，因而空氣進入。
The oil pipeline is worn, scratched or corroded, so air enters.
當空氣進入油中除引起過熱外，如果被壓縮的體積大約有20%是屬于被溶的空氣，則壓力下降時便會形成泡沫。
When air enters the oil, in addition to overheating, if the volume of the compressed volume is about 20% of the dissolved air, the foam will form when the pressure drops.
而工作液壓缸在減壓回油時，帶泡沫的油液就會形成“海綿”的性質。此外，油中含有許多泡沫會增加總體積，將造成油箱或儲油器的溢油現象。
When the working hydraulic cylinder is decompressed, the foam oil will form the sponge character. In addition, many bubbles in the oil will increase the total volume, causing oil spills or oil spills.
含有空氣的工作油，在傳遞動力時會產生急跳的痙攣現象，含有空氣的工作油，還會造成液壓泵發生氣穴的危險，由此而產生更大的吸力，會把更多的空氣連同其他雜質都吸入系統內。因油中進入空氣而產生過熱，空氣進入的同時也會帶進灰塵，這些情況會使油很快變質
The working oil containing air will produce jerk spasm when transmitting power. The working oil containing air will also cause the risk of cavitation of the hydraulic pump, resulting in greater suction, which will suck more air and other impurities into the system. Overheating is caused by air entering the oil, and dust will be brought in at the same time. These conditions will quickly deteriorate the oil
下一篇：混凝土攪拌制從未如此簡單!上一篇：混凝土自上料攪拌車墜橋剎車原因就是它
